![]() Rated watts 2ch x 2 ohms: 4750 watts 20ms repetitive burst 3750 watts 1% THD both channels driven 1kHz Rated watts 2ch x 4 ohms: 2800 watts 20ms repetitive burst 2450 watts 1% THD / 2020 watts 0.15% THD, both channels 1kHz Rated watts 2ch x 8 ohms: 1550 watts 20ms repetitive burst 1425 watts 1% THD / 1200 watts 0.15% THD, both channels 1kHz Dimensions (HxWxD): 3.5” x 19” x 10.5” behind front panel, +0. The added harmonics allow smaller speakers to produce more perceived bass than they would otherwise be able to produce with traditional amplifiers. By tricking the human ear into perceiving lower frequencies that are not actually present in the output of the original signal, MaxxBass® allows the IPR2 to produce extremely powerful bass at relatively low power. When these harmonics are combined with the original signal, it creates the effect of lower, deeper frequencies. MaxxBass® uses psycho-acoustics to calculate precise harmonics that are added to the original signal. Peavey CS800X power amplifier with Stereo mode: 2 Ohms at 600watts rms per channel and 1200 watts rms into 4 ohms in bridge mode.Can handle 2,4,8 speakers in stereo mode Automatic two-speed cooling fanIndependent channelTransient-freeTwo recessed balanced inputSingle XLRDual phone plug am plifier in excellent condition. Peavey ProBass500 This recent amp exhibits some of the alternative types of EQ, inputs. Hi-pass filters on every channel remove unwanted rumble and noise, and balanced AUX and Master outputs ensure a clean noise-free signal to your powered speakers or power amplifier. A cable is inserted here to connect to the mains power. This technology allows sound engineers to dial more perceived low-end into a system without adding more power amps, processing, or subwoofers. These revolutionary power amplifiers are the only power amps to integrate Waves® MaxxBass® technology, which uses psycho-acoustics to create precise harmonic overtones that give the illusion of adding low frequencies to the mix. Designed with a resonant switch-mode power supply and a high-speed class-D topology that yields the highest audio resolution and efficiency available - and all at a cost that shatters the old-guard paradigm of power-amp valuation. Low/Thru and High, TS ¼" (6.3 mm) Speakons for Chan A, Chan B and Bridge Binding PostsĨ.9 x 48.3 x 38.0 cm (3.5" x 19.0" x 15.PLEASE NOTE: IPR2 amplifiers are NOT designed to be powered on permanently.īoasting a net weight of just over 7lbs on the lightest model, the groundbreaking IPR2 Series utilizes an advanced design that allows our engineers to dramatically reduce weight while increasing output power, reliability, and thermal efficiency. Turn on/off muting, DC (triac crowbar), low-cut filterĮlectronic balanced Barrier Strip, XLR, TRS ¼" (6.3 mm) Red, DDT/clipping Yellow, signal Green, powerįull short circuit, open circuit over-temp thermal RF stable into any load Peavey Electronics proudly announces the immediate availability of the revolutionary Peavey IPR 3000 power amplifier. Rated Output Power - 1 kHz, 1% THD, Dual Channelįrequency Response (+0/-3dB, rated power) 2-rack-space stereo power amp featuring DDT™ protection.The PV 900 delivers 300 watts per side into 4 ohms, 180 watts into 8 ohms and features detented input gain controls. ![]() ![]() ![]() The new PV® Series power amps retain their two-channel design, high power points and exclusive Peavey features and technologies-such as DDT™ compression and Peavey patented Turbo-V™ Cooling. We always picture any and all accessories too. PV 900 - Call for pricing - Power Amplifier - 00512860 A Peavey M-3000 Power Amp in Very Good condition At Evolution Music of Orland Park, we attempt to highlight cosmetic defects (if any) by picturing every angle of every piece of gear so you know exactly what you are getting. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |